145 - MiTo   1.4 16v TJet   COOLING CIRCUIT INLET PIPE TO LPG SYSTEM PRESSURE REGULATOR - R.R.   1088D72   

Detail     Detail
Removing ( Refitting )

- Place the vehicle on a lift.

    Op. 7055B54 PROTECTION/GUARD UNDER ENGINE -R.R.

    Op. 0010T20 ENGINE COOLANT - CHANGE

    Op. 5530B10 BATTERY - R+R


Enlarge the image

1. Loosen the band and disconnect the cooling circuit pipe at the inlet of the LPG pressure regulator, three-way connector side.

Enlarge the image

1. Loosen the band and remove the cooling circuit pipe at the inlet of the LPG pressure regulator.
Refitting ( Removing )

- Place the coolant inlet circuit pipe in position to the LPG pressure regulator in position and tighten the bands.

    Op. 5530B10 BATTERY - R+R

    Op. 0010T20 ENGINE COOLANT - CHANGE

    Op. 7055B54 PROTECTION/GUARD UNDER ENGINE -R.R.

- Remove the vehicle from the lift.

APPLIES TO VERSIONS WITH: Euro 5

Removing ( Refitting )

- Place the car on a lift.

APPLIES TO VERSIONS WITH: Euro 5

    Op. 7055B54 PROTECTION/GUARD UNDER ENGINE -R.R.

    Op. 0010T20 ENGINE COOLANT - CHANGE

    Op. 5530B10 BATTERY - R+R

    Op. 5530B52 BATTERY SUPPORT/DRIP TRAY - R.R

APPLIES TO VERSIONS WITH: Euro 5


Enlarge the image

1. Undo the screws (1a) and move the engine coolant reservoir (1b) to one side.

APPLIES TO VERSIONS WITH: Euro 5


Enlarge the image

1. Open the band and disconnect the cooling circuit pipe at the inlet of the LPG pressure regulator, three-way connector side.

APPLIES TO VERSIONS WITH: Euro 5


Enlarge the image

1. Open the band and disconnect the cooling circuit pipe at the inlet of the LPG pressure regulator, pressure regulator side.

2. Open the retaining clips for the cooling circuit pipe at the inlet of the pressure regulator and remove it.

APPLIES TO VERSIONS WITH: Euro 5

Refitting ( Removing )

- Place the cooling circuit pipe at the inlet of the LPG pressure regulator back in its housing and fix it with the clips.

- Close the retaining band for the cooling circuit pipe at the inlet of the LPG pressure regulator, pressure regulator side.

Maintain a distance of 3 - 5 mm between the band and the end of the pipe.

- Close the retaining band for the cooling circuit pipe at the inlet of the LPG pressure regulator, three-way connector side.

Maintain a distance of 3 - 5 mm between the band and the end of the pipe.

- Place the engine coolant reservoir back in its housing and fix it with the screws.

APPLIES TO VERSIONS WITH: Euro 5

    Op. 5530B52 BATTERY SUPPORT/DRIP TRAY - R.R

    Op. 5530B10 BATTERY - R+R

    Op. 0010T20 ENGINE COOLANT - CHANGE

    Op. 7055B54 PROTECTION/GUARD UNDER ENGINE -R.R.

APPLIES TO VERSIONS WITH: Euro 5

- Remove the vehicle from the lift.

APPLIES TO VERSIONS WITH: Euro 6

Removing ( Refitting )

- Place the car on a lift.

APPLIES TO VERSIONS WITH: Euro 6

    Op. 7055B54 PROTECTION/GUARD UNDER ENGINE -R.R.

    Op. 0010T20 ENGINE COOLANT - CHANGE

    Op. 5530B10 BATTERY - R+R

    Op. 5530B52 BATTERY SUPPORT/DRIP TRAY - R.R

APPLIES TO VERSIONS WITH: Euro 6

Removing ( Refitting )

   Op. 7055B54 PROTECTION/GUARD UNDER ENGINE -R.R.

   Op. 0010T20 ENGINE COOLANT - CHANGE

   Op. 5530B10 BATTERY - R+R

   Op. 5530B52 BATTERY SUPPORT/DRIP TRAY - R.R

APPLIES TO VERSIONS WITH: Euro 6


Enlarge the image

1. Undo the screws (1a) and move the engine coolant reservoir (1b) to one side.

APPLIES TO VERSIONS WITH: Euro 6


Enlarge the image

1. Undo the screws (1a) and move the engine coolant reservoir (1b) to one side.

APPLIES TO VERSIONS WITH: Euro 6


Enlarge the image

1. Open the band and disconnect the cooling circuit pipe at the inlet of the LPG pressure regulator, three-way connector side.

APPLIES TO VERSIONS WITH: Euro 6


Enlarge the image

1. Open the band and disconnect the cooling circuit pipe at the inlet of the LPG pressure regulator, three-way connector side.

APPLIES TO VERSIONS WITH: Euro 6


Enlarge the image

1. Open the band and disconnect the cooling circuit pipe at the inlet of the LPG pressure regulator, pressure regulator side.

2. Open the retaining clips for the cooling circuit pipe at the inlet of the pressure regulator and remove it.

APPLIES TO VERSIONS WITH: Euro 6


Enlarge the image

1. Open the band and disconnect the cooling circuit pipe at the inlet of the LPG pressure regulator, pressure regulator side.

2. Open the retaining clips for the cooling circuit pipe at the inlet of the pressure regulator and remove it.

APPLIES TO VERSIONS WITH: Euro 6

Refitting ( Removing )

- Place the cooling circuit pipe at the inlet of the LPG pressure regulator back in its housing and fix it with the clips.

- Close the retaining band for the cooling circuit pipe at the inlet of the LPG pressure regulator, pressure regulator side.

Maintain a distance of 3 - 5 mm between the band and the end of the pipe.

- Close the retaining band for the cooling circuit pipe at the inlet of the LPG pressure regulator, three-way connector side.

Maintain a distance of 3 - 5 mm between the band and the end of the pipe.

- Place the engine coolant reservoir back in its housing and fix it with the screws.

APPLIES TO VERSIONS WITH: Euro 6

Refitting ( Removing )

- Place the cooling circuit pipe at the inlet of the LPG pressure regulator back in its housing and fix it with the clips.

- Close the retaining band for the cooling circuit pipe at the inlet of the LPG pressure regulator, pressure regulator side.

Maintain a distance of 3 - 5 mm between the band and the end of the pipe.

- Close the retaining band for the cooling circuit pipe at the inlet of the LPG pressure regulator, three-way connector side.

Maintain a distance of 3 - 5 mm between the band and the end of the pipe.

- Place the engine coolant reservoir back in its housing and fix it with the screws.

APPLIES TO VERSIONS WITH: Euro 6

    Op. 5530B52 BATTERY SUPPORT/DRIP TRAY - R.R

    Op. 5530B10 BATTERY - R+R

    Op. 0010T20 ENGINE COOLANT - CHANGE

    Op. 7055B54 PROTECTION/GUARD UNDER ENGINE -R.R.

APPLIES TO VERSIONS WITH: Euro 6

    Op. 5530B52 BATTERY SUPPORT/DRIP TRAY - R.R

    Op. 5530B10 BATTERY - R+R

    Op. 0010T20 ENGINE COOLANT - CHANGE

    Op. 7055B54 PROTECTION/GUARD UNDER ENGINE -R.R.

APPLIES TO VERSIONS WITH: Euro 6

- Remove the car from the lift.

APPLIES TO VERSIONS WITH: Euro 6

- Remove the car from the lift.