Refitting

- Drain the section of the pipe from the pressure regulator to the injectors, following the procedure and the instructions below

   Op. 1043A02 LPG SYSTEM LINES PIPE DRAINING OPERATIONS

- Return the car to the workshop (in petrol operation mode).

    Op. 5530B10 BATTERY - R+R

    Op. 5530B52 BATTERY SUPPORT/DRIP TRAY - R.R

1. Open the retaining clip for the pipe from pressure regulator to LPG filter.

2. Loosen the band and disconnect the pipe from pressure regulator to LPG filter, regulator side.

1. Open the retaining clips for the pipe from pressure regulator to LPG filter located on the rear engine compartment bulkhead.

1. Open the retaining clip for the LPG injector unit inlet pipe.

2. Undo the nut (2a) and remove the LPG filter fixing collar (2b).

1. Move the LPG filter as far as necessary, loosen the band and remove the pipe from pressure regulator to LPG filter.

Removing

- Connect the pipe from pressure regulator to LPG filter, filter side, then tighten the band.

Maintain a distance of 3 - 5 mm between the band and the end of the pipe.

- Place the LPG filter in position.

- Place the LPG filter fixing collar back in it housing and tighten the nut.

- Close the retaining clip for the LPG injector unit inlet pipe.

- Close the fixing clips for the pipe from pressure regulator to LPG filter located on the rear engine compartment bulkhead.

- Connect the pipe from pressure regulator to LPG filter, regulator side, then tighten the band.

Maintain a distance of 3 - 5 mm between the band and the end of the pipe.

- Close the remaining retaining clip for the pipe from pressure regulator to LPG filter.

    Op. 5530B52 BATTERY SUPPORT/DRIP TRAY - R.R

    Op. 5530B10 BATTERY - R+R

    Op. 1043A04 GPL SYSTEM AND PIPES CHECK FOR LEAKS

Refitting

- Drain the section of the pipe from the pressure regulator to the injectors, following the procedure and the instructions below

   Op. 1043A02 LPG SYSTEM LINES PIPE DRAINING OPERATIONS

- Return the car to the workshop (in petrol operation mode).

    Op. 5530B10 BATTERY - R+R

    Op. 5530B52 BATTERY SUPPORT/DRIP TRAY - R.R

1. Open the retaining clip for the pipe from pressure regulator to LPG filter.

2. Loosen the band and disconnect the pipe from pressure regulator to LPG filter, regulator side.

1. Open the retaining clips for the pipe from pressure regulator to LPG filter located on the rear engine compartment bulkhead.

1. Open the retaining clip for the LPG injector unit inlet pipe.

2. Undo the nut (2a) and remove the LPG filter fixing collar (2b).

1. Move the LPG filter as far as necessary, loosen the band and remove the pipe from pressure regulator to LPG filter.

Removing

- Connect the pipe from pressure regulator to LPG filter, filter side, then tighten the band.

Maintain a distance of 3 - 5 mm between the band and the end of the pipe.

- Place the LPG filter in position.

- Place the LPG filter fixing collar back in it housing and tighten the nut.

- Close the retaining clip for the LPG injector unit inlet pipe.

- Close the fixing clips for the pipe from pressure regulator to LPG filter located on the rear engine compartment bulkhead.

- Connect the pipe from pressure regulator to LPG filter, regulator side, then tighten the band.

Maintain a distance of 3 - 5 mm between the band and the end of the pipe.

- Close the remaining retaining clip for the pipe from pressure regulator to LPG filter.

    Op. 5530B52 BATTERY SUPPORT/DRIP TRAY - R.R

    Op. 5530B10 BATTERY - R+R

    Op. 1043A04 GPL SYSTEM AND PIPES CHECK FOR LEAKS