145 - MiTo   1.4 16v TJet   LPG FILTER ON PRESSURE REGULATOR - R.R.   1057B61   

Detail     Detail
Removing ( Refitting )

- Drain the pipe from tank to LPG pressure regulator, following the procedures and the instructions below

   Op. 1043A02 LPG SYSTEM LINES PIPE DRAINING OPERATIONS

- Return the vehicle to the workshop (in petrol operation mode) and place it on a lift.

- Disconnect the negative battery terminal.

    Op. 7055B54 PROTECTION/GUARD UNDER ENGINE -R.R.

    Op. 0010T20 ENGINE COOLANT - CHANGE

    Op. 1043B40 PRESSURE REGULATOR FOR LPG SUPPLY - R.R.

- Position the LPG pressure regulator in a vice fitted with protective jaws.

Enlarge the image

1. Release the flexible ring and remove the solenoid valve - LPG filter unit.

Enlarge the image

1. Extract the cut out solenoid valve (1a) and the LPG filter (1b).

2. Remove the O-ring shown in the picture.
Refitting ( Removing )

- Fit a new O-ring in the seat.

- Place the new LPG filter and the cut out solenoid valve in position.

- Place the solenoid valve - LPG filter unit in position and engage the flexible retaining ring.

- Remove the LPG pressure regulator from the vice.

    Op. 1043B40 PRESSURE REGULATOR FOR LPG SUPPLY - R.R.

    Op. 0010T20 ENGINE COOLANT - CHANGE

    Op. 7055B54 PROTECTION/GUARD UNDER ENGINE -R.R.

- Connect the negative battery terminal.

- Remove the vehicle from the lift.

    Op. 1043A04 GPL SYSTEM AND PIPES CHECK FOR LEAKS

APPLIES TO VERSIONS WITH: Euro 5

Removing ( Refitting )

- Drain the pipe from tank to pressure regulator, following the procedures and the instructions below

   Op. 1043A02 LPG SYSTEM LINES PIPE DRAINING OPERATIONS

- Return the car to the workshop (in petrol operation mode).

APPLIES TO VERSIONS WITH: Euro 5

    Op. 7055B54 PROTECTION/GUARD UNDER ENGINE -R.R.

APPLIES TO VERSIONS WITH: Euro 5


Enlarge the image



Enlarge the image

1. Disconnect the electrical connection for the LPG cut out solenoid valve coil on the pressure regulator.

 

 

Denomination

  

Connector
 

1

  

LPG cut out solenoid valve

  

   See L063 GPL CUT OUT SOLENOID VALVE

1. Open the two retaining clips for the supply pipe from tank to LPG pressure regulator, located on the regulator mounting bracket.

2. Undo the screws fixing the LPG pressure regulator mounting bracket.

APPLIES TO VERSIONS WITH: Euro 5


Enlarge the image

1. Undo the screws (1a) and remove the LPG filter cover (1b).

APPLIES TO VERSIONS WITH: Euro 5


Enlarge the image

1. Remove the LPG filter from the pressure regulator.

APPLIES TO VERSIONS WITH: Euro 5


Enlarge the image

1. Remove the O-rings from the LPG filter mounting.

APPLIES TO VERSIONS WITH: Euro 5

Refitting ( Removing )

- Fit a new O-rings on the LPG filter mounting.

- Place the LPG filter in position.

- Place the LPG filter cover in its housing and tighten the screws.

APPLIES TO VERSIONS WITH: Euro 5


Enlarge the image

1. Tighten the screws fixing the LPG pressure regulator to the mounting bracket to the prescribed torque.

2. Close the two retaining clips for the supply pipe from tank to LPG pressure regulator, located on the regulator mounting bracket.

APPLIES TO VERSIONS WITH: Euro 5

- Connect the electrical connection for the LPG cut out solenoid valve coil on the pressure regulator.

APPLIES TO VERSIONS WITH: Euro 5

    Op. 7055B54 PROTECTION/GUARD UNDER ENGINE -R.R.

APPLIES TO VERSIONS WITH: Euro 5

- Remove the vehicle from the lift.

APPLIES TO VERSIONS WITH: Euro 5

    Op. 1043A04 GPL SYSTEM AND PIPES CHECK FOR LEAKS

APPLIES TO VERSIONS WITH: Euro 6

    Op. 7055B54 PROTECTION/GUARD UNDER ENGINE -R.R.

APPLIES TO VERSIONS WITH: Euro 6


Enlarge the image

1. Disconnect the electrical connection for the LPG cut out solenoid valve coil on the pressure regulator.

 

 

Name

  

Connector
 

1

  

LPG cut out solenoid valve

  

   See L063 GPL CUT OUT SOLENOID VALVE

APPLIES TO VERSIONS WITH: Euro 6


Enlarge the image

1. Open the two retaining clips for the supply pipe from tank to LPG pressure regulator, located on the regulator mounting bracket.

2. Undo the screws fixing the LPG pressure regulator mounting bracket.

APPLIES TO VERSIONS WITH: Euro 6


Enlarge the image

1. Undo the screws (1a) and remove the LPG filter cover (1b).

APPLIES TO VERSIONS WITH: Euro 6


Enlarge the image

1. Remove the LPG filter from the pressure regulator.

APPLIES TO VERSIONS WITH: Euro 6


Enlarge the image

1. Remove the O-rings from the LPG filter mounting.

APPLIES TO VERSIONS WITH: Euro 6

Refitting ( Removing )

- Fit a new O-rings on the LPG filter mounting.

- Place the LPG filter in position.

- Place the LPG filter cover in its housing and tighten the screws.

APPLIES TO VERSIONS WITH: Euro 6


Enlarge the image

1. Tighten the screws fixing the LPG pressure regulator to the mounting bracket to the prescribed torque.

2. Close the two retaining clips for the supply pipe from tank to LPG pressure regulator, located on the regulator mounting bracket.

APPLIES TO VERSIONS WITH: Euro 6

- Connect the electrical connection for the LPG cut out solenoid valve coil on the pressure regulator.

APPLIES TO VERSIONS WITH: Euro 6

    Op. 7055B54 PROTECTION/GUARD UNDER ENGINE -R.R.

APPLIES TO VERSIONS WITH: Euro 6

- Remove the car from the lift.

APPLIES TO VERSIONS WITH: Euro 6

    Op. 1043A04 GPL SYSTEM AND PIPES CHECK FOR LEAKS