			Test results
1	COMPONENT CONCERNED	FUSE CONDITION CHECK	OK (NO FAULTS DETECTED)	FAULT DETECTED	ACTION
	Fuse	Check the condition of the cigar lighter fuse	Go to Step 2	Fuse damaged	Replace the fuse and try to determine the cause of the malfunction
2	COMPONENT CONCERNED	CIGAR LIGHTER PLUG OPERATION CHECK	OK (NO FAULTS DETECTED)	FAULT DETECTED	ACTION
	Cigar lighter plug	Operate the base of the cigar lighter plug and check that latter remains engaged (the ignition coil must remain attached to the bi-metal clip at the bottom of the sleeve). If it is not attached, remove the plug from the sleeve and visually inspect the condition of the bi-metal strip.	Go to Step 3	Following operation, the cigar lighter plug’s ignition coil is not retained by the bi-metal clip due to deformation of the clip itself.	Replace the cigar lighter sleeve
3	COMPONENT CONCERNED	IGNITION COIL CONDITION CHECK	OK (NO FAULTS DETECTED)	FAULT DETECTED	ACTION
	Cigar lighter plug	Remove the plug from the sleeve and visually inspect the condition of the ignition coil	Go to Step 4	Resistance broken or melted	Replace the cigar lighter plug
4	COMPONENT CONCERNED	RESISTANCE FASTENING CHECK	OK (NO FAULTS DETECTED)	FAULT DETECTED	ACTION
	Cigar lighter plug	Remove the plug from the sleeve and visually inspect the resistance to determine whether it is fixed correctly to the central pin	Go to Step 5	Resistance moves/has come out	Replace the cigar lighter plug
5	COMPONENT CONCERNED	CIGAR LIGHTER PLUG CHECK	OK (NO FAULTS DETECTED)	FAULT DETECTED	ACTION
	Cigar lighter plug	Remove the cigar lighter plug from the sleeve and check that it is entirely complete. The grip and the base must be arranged correctly	Go to Step 6	Cigar lighter plug without grip or grip/base damaged	Replace the cigar lighter plug
6	COMPONENT CONCERNED	BASE TRAVEL CHECK	OK (NO FAULTS DETECTED)	FAULT DETECTED	ACTION
	Knob	Check that the movement/travel of the base is complete and regular, and that it occurs in a linear, smooth fashion, without sticking (possible foreign elements inside the plug or ceramic shards/fragments).	Go to Step 7	Moving parts do not slide	Replace the cigar lighter plug
7	COMPONENT CONCERNED	CIGAR LIGHTER PLUG CONDITION CHECK	OK (NO FAULTS DETECTED)	FAULT DETECTED	ACTION
	Cigar lighter plug	Check for the absence of mechanical deformation on the ignition coil and the condition of the internal ceramic elements by pressing the base and visual inspection	Go to Step 8	Cigar lighter plug with mechanical deformation or ovalised	Replace the cigar lighter plug
8	COMPONENT CONCERNED	IGNITION COIL RESISTANCE CHECK	OK (NO FAULTS DETECTED)	FAULT DETECTED	ACTION
	Ignition coil	Check that the resistance value between the central pin and the heater coil is between 0.5 and 1,5 Ω	Go to Step 9	Incorrect resistance value	Replace the cigar lighter plug
9	COMPONENT CONCERNED	SLEEVE CONNECTIONS CHECK	OK (NO FAULTS DETECTED)	FAULT DETECTED	ACTION
	Cigar lighter sleeve connections	Check that the connections between the cable loom connector and the power socket connector are correct	Go to Step 10	Connector has come out	Restore the correct connections
10	COMPONENT CONCERNED	SLEEVE SUPPLY CHECK	OK (NO FAULTS DETECTED)	FAULT DETECTED	ACTION
	Sleeve	Using a multimeter, connect the probes to the central rivet (+) and the sleeve flange (-) and check for the presence of a supply voltage of approximately 13.5. This test should be carried out with the battery charged and engine running. Then insert the plug and engage the lighter. If the release time is between 8 and 20 seconds, the component is operational.	Go to Step 11	Voltage value below 10 V (measured with car in motion).	Check electrical system
11	COMPONENT CONCERNED	SLEEVE CONDITION CHECK	OK (NO FAULTS DETECTED)	FAULT DETECTED	ACTION
	Sleeve	Check for the absence of contamination by fluids or other substances or oxidation inside the sleeve	Go to Step 12	Sleeve oxidised	Replace the sleeve
12	COMPONENT CONCERNED	SLEEVE CONDITION CHECK	OK (NO FAULTS DETECTED)	FAULT DETECTED	ACTION
	Sleeve	Check for the absence of metal deformation on the sleeve and its fins (plug treatment)	Go to Step 13	Presence of mechanical deformation on the sleeve and its fins	Replace the sleeve
13	COMPONENT CONCERNED	RING NUT CONDITION CHECK	OK (NO FAULTS DETECTED)	FAULT DETECTED	ACTION
	Ring nut	Using special pliers, remove the sleeve from the ring nut and check that there are no breaks or deformation	Go to Step 14	Presence of breaks or deformation	Replace the plastic fitting ring nut
14	COMPONENT CONCERNED	CORRECT ILLUMINATED RING NUT SUPPLY CHECK	OK (NO FAULTS DETECTED)	FAULT DETECTED	ACTION
	Ring nut	Check for a supply voltage of approximately 13.5. This test should be carried out with the battery charged and car in motion.	End of diagnosis	No supply Fitting ring nut not illuminated	Restore the correct power supply Replace ring nut Op. 7065C86 CURRENT SOCKET IN LUGGAGE COMPARTMENT - R.R.