145 - MiTo   1.4 16v TJet   FRONT FUEL DELIVERY LINE - R.R.   1040B32   

Detail     Detail

Removing ( Refitting )

- Open the fuse box cover in the engine compartment, remove fuse F21 (15 A) and start the engine several times until the fuel pressure in the distribution manifold is relieved.

- Fit the fuse removed previously and close the fuse box casing.

- Place the vehicle on a lift.

    Op. 0010T84 AIR CONDITIONING SYSTEM REFRIGERANT - DEHYDRATING AND REPRESSURIZING

    Op. 1016A10 SOUND-PROOFING COVER - R.R

    Op. 7055B54 PROTECTION/GUARD UNDER ENGINE -R.R.

    Op. 4450B04 RIGHT FRONT WHEEL - R.R.

    Op. 7055B66 ENGINE COMPARTMENT DUST COVER IN RIGHT FRONT WHEEL ARCH - R.R.

    Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.

    Op. 1092G10 AUXILIARY COMPONENTS SINGLE DRIVE BELT - R.R.

    Op. 5040A20 AIR CONDITIONING COMPRESSOR - R.R. INCLUDES CHECKING FLUID LEVEL AND TOPPING UP IF NECESSARY

    Op. 5540C42 SENSOR FOR CORRECTING/ALIGNING GAS DISCHARGE LIGHT CLUSTERS ON FRONT SUSPENSION - R.R.

    Op. 1076B72 INTERMEDIATE EXHAUST PIPE WITH HOSE SECTION - R+R

    Op. 1008C32 GEARBOX LOWER REACTION ROD -R.R.

    Op. 1040E22 FUEL PIPE PROTECTION - R.R


Enlarge the image


1. Disconnect the rapid connector (1a) and release the front fuel supply pipe from the retaining clip (1b).


Enlarge the image


1. Disconnect the rapid connector and release the front fuel supply pipe from the retaining clips.


Enlarge the image


1. Undo the screws fixing the steering box to the suspension cross member.

- Position a hydraulic lift under the suspension cross member.


Enlarge the image


1. Undo the bolts securing the front suspension crossmember to the body.

- Use the hydraulic hoist to lower the suspension cross member and remove the front fuel delivery pipe.

Refitting ( Removing )

- Refit the front fuel delivery pipe in its housing and engage the intermediate retaining clips.

- Connect the rear quick connector for the front fuel supply pipe.


Enlarge the image


1. Place the suspension crossmember in its housing and tighten the bolts to the recommended torque.

 

Component

 

Fixing

 

dia

 

Value (daNm)

 

Validity

 

Front suspension crossmember to body

 

Screw

 

M12

 

12.1 ÷ 14.8

 

- Remove the hydraulic lift.


Enlarge the image


1. Tighten the screws securing the steering box to the suspension cross member to the prescribed torque.

 

Component

 

Fixing

 

dia

 

Value (daNm)

 

Validity

 

Steering box to suspension crossmember

 

Bolt

 

M12

 

9.0 ÷ 11.0

 

- Connect the front rapid connector for the front fuel supply pipe and attach the intermediate retaining clips.

    Op. 1040E22 FUEL PIPE PROTECTION - R.R

    Op. 1008C32 GEARBOX LOWER REACTION ROD -R.R.

    Op. 1076B72 INTERMEDIATE EXHAUST PIPE WITH HOSE SECTION - R+R

    Op. 5540C42 SENSOR FOR CORRECTING/ALIGNING GAS DISCHARGE LIGHT CLUSTERS ON FRONT SUSPENSION - R.R.

    Op. 5040A20 AIR CONDITIONING COMPRESSOR - R.R. INCLUDES CHECKING FLUID LEVEL AND TOPPING UP IF NECESSARY

    Op. 1092G10 AUXILIARY COMPONENTS SINGLE DRIVE BELT - R.R.

    Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.

    Op. 7055B66 ENGINE COMPARTMENT DUST COVER IN RIGHT FRONT WHEEL ARCH - R.R.

    Op. 4450B04 RIGHT FRONT WHEEL - R.R.

    Op. 7055B54 PROTECTION/GUARD UNDER ENGINE -R.R.

    Op. 1016A10 SOUND-PROOFING COVER - R.R

    Op. 0010T84 AIR CONDITIONING SYSTEM REFRIGERANT - DEHYDRATING AND REPRESSURIZING

- Remove the vehicle from the lift.


Enlarge the image


1. Place the suspension crossmember in its housing and tighten the bolts to the recommended torque.

 

Component

 

Fixing

 

dia

 

Value (daNm)

 

Validity

 

Front suspension crossmember to body

 

Screw

 

M12

 

12.1 ÷ 14.8

 

- Connect the quick connector for the front fuel supply pipe, distribution manifold side, and engage the retaining clips.

    Op. 1092G10 AUXILIARY COMPONENTS SINGLE DRIVE BELT - R.R.

    Op. 1048A10 AIR FILTER ASSEMBLY - R.R.