145 - MiTo   1.4 16v TJet   DIPPED BEAM (ONE) RH OR LH NOT WORKING   I007   


 

 

 

Test results

 

1

 

BULB CONDITION CHECK.

 

All OK

 

Problems encountered

 

Operation

 

 

Check the continuity of the bulb filament

 

Move on to Step 2

 

Bulb inefficient

 

Replace the bulb

 Op. 5540B25 LOW BEAM BULB (ONE) FOR ONE HEADLAMP/LIGHT CLUSTER LH OR RH - R.R

 

2

 

ELECTRICAL SYSTEM CHECK.

 

All OK

 

Problems encountered

 

Operation

 

 

Check the condition of the bulb protective fuse

 See E2011 DIPPED HEADLAMPS

 

Move on to Step 3

 

Fuse blown

 

Replace the fuse and search for the cause of the malfunction.

 

3

 

ELECTRICAL SYSTEM CHECK.

 

All OK

 

Problems encountered

 

Operation

 

 

Check the continuity and the insulation of the wiring between the bulb and the Body Computer

 See E2011 DIPPED HEADLAMPS

 

Move on to Step 4

 

Electrical connection break or short circuit

 

Restore the correct electrical connection.

 

4

 

LAMP ELECTRICAL SYSTEM CHECK.

 

All OK

 

Problems encountered

 

Operation

 

 

Check the condition of the internal headlamp connections between the connector and bulb holder

 

Move on to Step 5

 

Internal connections interrupted or lacking insulation.

 

Restore the electrical connection, replacing the lamp if necessary

 

5

 

BODY COMPUTER OPERATION CHECK

 

All OK

 

Problems encountered

 

Operation

 

 

Check that the Body computer is working properly

 

End of diagnosis

 

Body Computer defective

 

Replace the body computer

 Op. 5505A35 MAIN BODY COMPUTER/JUNCTION UNIT - R.R.

APPLIES TO VERSIONS WITH: Gas discharge headlamps

 

 

TEST RESULTS

 

1

 

HEADLAMP CONNECTOR CHECK

 

ALL OK

 

PROBLEMS ENCOUNTERED

 

ACTION

 

 

Check that the 14-way connector at the right/left headlamp is correctly fitted

 

Move on to Step 2

 

Connector not correctly fitted

 

Refit correctly

 See E2011 DIPPED HEADLAMPS

 

2

 

DIPPED HEADLAMPS POWER SUPPLY CHECK

 

ALL OK

 

PROBLEMS ENCOUNTERED

 

ACTION

 

 

Turn the steering wheel interface lever to the dipped headlamps position and check that the voltage at the headlamps is correct

 See Test 5540BA DIPPED BEAM CIRCUIT CHECK

 

Move on to Step 4

 

 

 

3

 

CHECK ON OPERATION OF BULB

 

ALL OK

 

PROBLEMS ENCOUNTERED

 

ACTION

 

 

Check, that when the bulb is replaced,

 Op. 5540B45 GAS DISCHARGE LOW/MAIN BEAM HEADLAMP BULB - R.R.

the fault disappears

 

End of diagnosis

 

The fault persists

 

Refit the original bulb.

 

4

 

CHECK ON CORRECT OPERATION OF HEADLAMP

 

ALL OK

 

PROBLEMS ENCOUNTERED

 

ACTION

 

 

Replace the left headlamp

 Op. 5540B81 LEFT GAS DISCHARGE LIGHT CLUSTER - R.R.

or right headlamp

 Op. 5540B82 RIGHT GAS DISCHARGE LIGHT CLUSTER - R.R.

(the failed unit) and check it is working properly

 

End of diagnosis

 

The fault persists

 

Refit the headlamp replaced previously.

 

5

 

CORRECT OPERATION CHECK

 

ALL OK

 

PROBLEMS ENCOUNTERED

 

ACTION

 

 

Replace the faulty headlamp ballast control unit

 Op. 5540B40 CONTROL UNIT IN LEFT GAS DISCHARGE LIGHT CLUSTER - R.R.

 Op. 5540B41 CONTROL UNIT IN RIGHT GAS DISCHARGE LIGHT CLUSTER - R.R.

 

End of diagnosis

 

 

Note: One of the two dipped headlamps is not working;