|
|
|
Test results |
|
|
Connect the Examiner diagnostic equipment and check, in Electric Steering Node Parameter Reading mode, that there are no errors and that the parameters are present. |
Proceed to Step 9 |
Impossible to connect to the control unit. |
Move on to Step 2 |
|
Presence of errors. |
Move on to Step 6 |
|
Low battery voltage parameter reading. |
Move on to Step 8 |
|
|
Check the electrical power supply to the Electric Steering Node is correct. With the panel off, check for a voltage of around 12.5V at the blue power supply connector. With the panel on, check for the same voltage at PIN 1 of the black connector for the CAN line signals. See E7045 ELECTRIC STEERING |
Move on to Step 3 |
Battery voltage faulty. |
Move on to Step 8 |
|
Fault in positive electrical supply and/or earth. |
Replace the component causing the problem (in the case of a fuse, find out what caused the damage). |
|
|
Check the electrical connections for the Electric Steering Node and the Body Computer, searching for any loose connections creating occasional breaks in the power supply. In particular, make sure that every PIN is correctly connected and fitted in place. Take GREAT care over the positive battery terminal leading to the 70 A fuse for the electric steering (left terminal). If it is secured but NOT correctly fitted in place, disconnect it and fasten it correctly. See E7045 ELECTRIC STEERING |
Move on to Step 4 |
Electrical connections not working. |
Restore the damaged electrical connections. |
|
|
Start up the engine and then switch it off. At this point, with the panel off, check that the voltage at PIN 1 of the black connector for the CAN line signals is effective 0V. See E7045 ELECTRIC STEERING |
Move on to Step 5 |
The voltage at PIN 1 with the panel off is more than 0 V. |
DO NOT replace the Electric Steering Assembly. Electrical equipment problem. Contact TESEO. |
|
|
Recheck the possibility of connecting to the Electric Steering Node using the Examiner. |
Move on to Step 1 |
Impossible to connect to the control unit. |
Replace the Electric Steering assembly. Op. 4110D20 STEERING ELECTRICAL CONTROL DEVICE - R R |
|
|
Check for the presence of one or more of the following errors using the Examiner in Electric Steering Node mode: - C1214, incorrect end of line configuration. - C1001, internal control unit error. - C1002, steering column torque/position sensor error - C1008, position sensor not calibrated. - C1200, services battery error. - C1003 or U1700 or U1701, Body Computer node/vehicle speed errors. - U0001, CAN error |
End of diagnosis. |
Error C1214 detected, incorrect end of line calibration (there is no lack of power assistance). |
DO NOT replace the Electric Steering assembly. This is not an error but the normal system configuration. If the error is still present, check the vehicle proxy settings but do not replace the Electric Steering unit. |
|
Internal control unit error detected (C1001). |
Replace the Electric Steering assembly. Op. 4110D20 STEERING ELECTRICAL CONTROL DEVICE - R R |
|
Steering column torque/position sensor fault (C1002). |
Move on to Step 10. |
|
Position sensor not calibrated (C1008, there is no lack of power assistance). |
DO NOT replace the Electric Steering Assembly. Move on to Step 14. |
|
Services battery faulty (C1200, there is no lack of power assistance). |
DO NOT replace the Electric Steering Assembly. Move on to Step 8. |
|
Body Computer node / vehicle speed faulty (C1003, U1700 or U1701, there is no lack of power assistance). |
DO NOT replace the Electric Steering Assembly. Move on to Step 7. |
|
CAN faulty (U0001, there is no lack of power assistance). |
DO NOT replace the Electric Steering assembly. CAN problem. Move on to Step 7. |
|
|
Check and clean the earths. Check for the presence of similar errors in other devices on the vehicle. Check operation of the Engine management and Body Computer Node Check the CAN connections. Delete the error(s) and carry out a road test, checking that the fault is no longer present. |
End of diagnosis |
The error occurs again. |
DO NOT replace the Electric Steering assembly. Vehicle signals problem. Contact TESEO |
|
|
Check the following, in order: - Battery supply voltage level correct. - Power connection correct between battery, earth and Electric Steering Assembly connector. See E1010 POWER SUPPLY |
End of diagnosis. |
Services battery voltage faulty. |
Restore the correct operation of the battery. |
|
Loose connections detected in the Electric Steering Node power supply circuit |
Repair the wiring |
|
|
Check the electrical connections for the Electric Steering Node, searching for any loose connections creating occasional breaks in the power supply. In particular, make sure that every PIN is correctly connected and fitted in place. See E7045 ELECTRIC STEERING |
End of diagnosis. |
Electrical connections not working. |
Restore the damaged electrical connections. |
|
|
Using the Examiner in Electric Steering Node mode, after having confirmed the presence of the error, go to the error parameters screen and identify the Temporary Electric Steering Error item. |
- |
Temporary Electric Steering Error 23. |
Move on to Step 11. |
|
Temporary Electric Steering Error 19 |
Move on to Step 12. |
|
Temporary Electric Steering Error 32 or 25. |
Move on to Step 11. |
|
Temporary Electric Steering Error 99 (there is no lack of power assistance). |
DO NOT replace the Electric Steering Unit. Possible incorrect installation of system in vehicle. Check that the intermediate shaft is properly installed in the correct angular position. |
|
|
Check that the leads are correctly fastened at the battery terminals, in particular the earth lead at the negative pole. Also check that the 8-way connector is correctly fitted and securely fastened. See E1010 POWER SUPPLY |
- |
Wiring or connections defective. |
Restore the correct operation of the wiring and move on to Step 13 |
|
If no faults are detected in the wiring and the connections. |
Replace the Electric Steering assembly. Op. 4110D20 STEERING ELECTRICAL CONTROL DEVICE - R R |
|
|
Thoroughly clean the Electric Steering Node earths, also checking the condition of the wiring and making sure that the 8-way connector is correctly inserted and securely fastened. See E7045 ELECTRIC STEERING |
Move on to Step 13. |
The problem occurs again after the electrical checks. |
Replace the Electric Steering Assembly. Op. 4110D20 STEERING ELECTRICAL CONTROL DEVICE - R R |
|
|
After having cleaned the earths and checked the wiring, with the Examiner in Electric Steering Node mode, delete the error and carry out a road test. |
End of diagnosis. |
The problem occurs again. |
Replace the Electric Steering assembly. Op. 4110D20 STEERING ELECTRICAL CONTROL DEVICE - R R |
|
|
Using the Examiner, in Electric Steering Node mode, select the Position sensor calibration option and check the result of the operation. |
End of diagnosis. |
Impossible to calibrate the position sensor. |
DO NOT replace the Electric Steering Unit. Possible incorrect installation of system in vehicle. Check that the intermediate shaft is correctly fitted, above all if it has recently been replaced or disconnected. Check that it is fitted in the correct angular position. Using the Examiner, display the Steering angle position item. With the steering wheel straight and the wheels straight the value should be =0°. |