145 - MiTo   1.4 16v TJet   AIR BAG MODULE - PASSENGER SIDE - R.R   5580C22   

Detail     Detail
Removing ( Refitting )

Before removing and refitting the airbag module the following preliminary operations must be carried out.

- Turn the ignition key to “STOP” and extract it;

- Disconnect the battery cables and insulate them.

- Wait for 10 seconds before continuing.

FOLLOW ALL THE PRESCRIBED SAFETY INSTRUCTIONS (5580C - Introduction).

   Op. 5580C AIR BAG SYSTEM

   Op. 7040G20 BULB HOLDER FOR COMPARTMENT LIGHTING IN DASHBOARD - R.R.

   Op. 7040A31 DASHBOARD COMPARTMENT ASSEMBLY - R.R.


Enlarge the image

1. Undo the screws.

2. Move the airbag module slightly.

3. Disconnect the electrical connections (3a) and (3b).

 

 

Name

  

Connector
 

3

  

AIRBAG ON DASHBOARD (PASSENGER SIDE)

  

   See Q011 AIR BAG IN DASHBOARD (PASSENGER SIDE)

- Place the airbag module in the special cupboard, resting it on a free surface with the bag facing upwards.

Enlarge the image


 Refitting ( Removing )

- Observe the following precaution.

Handle the airbag module very carefully. Make sure that the battery is disconnected.

If a new module is installed, remove the detachable part of the adhesive label (if any) from the new module and place it in the special folder containing the vehicle details (model, registration date, chassis number) and the serial number of the old module. The folder must be kept for any checks necessary.

1. Connect the electrical connections (1a) and (1b).

2. Position the airbag module.

3. Tighten the screws.

    Op. 7040A31 DASHBOARD COMPARTMENT ASSEMBLY - R.R.

    Op. 7040G20 BULB HOLDER FOR COMPARTMENT LIGHTING IN DASHBOARD - R.R.

- Connect the battery.

- Use an Examiner to check that the system has not acquired errors during the operation.

APPLIES TO VERSIONS WITH: Right-hand drive

Removing ( Refitting )

Before removing and refitting the airbag module the following preliminary operations must be carried out.

- Turn the ignition key to “STOP” and extract it;

- Disconnect the battery cables and insulate them.

- Wait for 10 seconds before continuing.

FOLLOW ALL THE PRESCRIBED SAFETY INSTRUCTIONS (5580C - Introduction).

   Op. 5580C AIR BAG SYSTEM

APPLIES TO VERSIONS WITH: Right-hand drive


Enlarge the image

1. Open the dashboard compartment.

APPLIES TO VERSIONS WITH: Right-hand drive


Enlarge the image

1. Release the end of travel retainers (1a) and lower the dashboard compartment (1b).

APPLIES TO VERSIONS WITH: Right-hand drive


Enlarge the image

1. Undo the screws.

2. Move the airbag module slightly.

3. Disconnect the electrical connections (3a) and (3b).

 

 

Name

  

Connector
 

3

  

AIRBAG ON DASHBOARD (PASSENGER SIDE)

  

   See Q011 AIR BAG IN DASHBOARD (PASSENGER SIDE)

APPLIES TO VERSIONS WITH: Right-hand drive

- Place the airbag module in the special cupboard, resting it on a free surface with the bag facing upwards.

APPLIES TO VERSIONS WITH: Right-hand drive

Refitting ( Removing )

- Observe the following precaution.

Handle the airbag module very carefully. Make sure that the battery is disconnected.

If a new module is installed, remove the detachable part of the adhesive label (if any) from the new module and place it in the special folder containing the vehicle details (model, registration date, chassis number) and the serial number of the old module. The folder must be kept for any checks necessary.

APPLIES TO VERSIONS WITH: Right-hand drive


Enlarge the image

1. Connect the electrical connections (1a) and (1b).

2. Position the airbag module.

3. Tighten the screws.

APPLIES TO VERSIONS WITH: Right-hand drive

- Lift the dashboard compartment and engage the end of travel retainers.

- Close the glove compartment.

- Connect the battery.

- Use an Examiner to check that the system has not acquired errors during the operation.